RSM50W.jpg
RSM50W.jpg

Replacement Surge Module for 50A WiFi Units (GEN II + Powercenter)

$54.99

50A WiFi  Surge Protection Module

*** This replacement surge protection module is only for the PWD50EPOW, PWD50EPOHW, PWD50W, 50 AMP Powercenter units.  It is designed for use only with the 50 Amp 'generation 2' WiFi units. *** THIS IS NOT COMPATIBLE WITH GEN 1 UNITS!

Simple installation! The only tool required is a Phillips screw driver.

INSTRUCTIONS

  • UNPLUG THE UNIT - make sure unit is fully disconnected from power prior to installation.

  • Unscrew 6 Phillips screws on the back of the unit (*7 screws for the EPO versions).

  • Unscrew the top cable gland nut and move it up the cord.

  • The surge module slides in/out of the slot. Unclip the one red/black wire, and loosen the screws holding the fork wire connectors to the wire leads.

  • Unplug the old surge module from the unit.

  • Connect the new surge protection module and wires. "G" is ground and green color, "N" is neutral and white color, "L

  • Replace all the screws and re-tighten the cable gland nuts.

  • PART NUMBER: RSM50W

CAUTION!

Make sure unit is unplugged before installation!

Quantity:
Add To Cart

50A WiFi  Surge Protection Module

*** This replacement surge protection module is only for the PWD50EPOW, PWD50EPOHW, PWD50W, 50 AMP Powercenter units.  It is designed for use only with the 50 Amp 'generation 2' WiFi units. *** THIS IS NOT COMPATIBLE WITH GEN 1 UNITS!

Simple installation! The only tool required is a Phillips screw driver.

INSTRUCTIONS

  • UNPLUG THE UNIT - make sure unit is fully disconnected from power prior to installation.

  • Unscrew 6 Phillips screws on the back of the unit (*7 screws for the EPO versions).

  • Unscrew the top cable gland nut and move it up the cord.

  • The surge module slides in/out of the slot. Unclip the one red/black wire, and loosen the screws holding the fork wire connectors to the wire leads.

  • Unplug the old surge module from the unit.

  • Connect the new surge protection module and wires. "G" is ground and green color, "N" is neutral and white color, "L

  • Replace all the screws and re-tighten the cable gland nuts.

  • PART NUMBER: RSM50W

CAUTION!

Make sure unit is unplugged before installation!

50A WiFi  Surge Protection Module

*** This replacement surge protection module is only for the PWD50EPOW, PWD50EPOHW, PWD50W, 50 AMP Powercenter units.  It is designed for use only with the 50 Amp 'generation 2' WiFi units. *** THIS IS NOT COMPATIBLE WITH GEN 1 UNITS!

Simple installation! The only tool required is a Phillips screw driver.

INSTRUCTIONS

  • UNPLUG THE UNIT - make sure unit is fully disconnected from power prior to installation.

  • Unscrew 6 Phillips screws on the back of the unit (*7 screws for the EPO versions).

  • Unscrew the top cable gland nut and move it up the cord.

  • The surge module slides in/out of the slot. Unclip the one red/black wire, and loosen the screws holding the fork wire connectors to the wire leads.

  • Unplug the old surge module from the unit.

  • Connect the new surge protection module and wires. "G" is ground and green color, "N" is neutral and white color, "L

  • Replace all the screws and re-tighten the cable gland nuts.

  • PART NUMBER: RSM50W

CAUTION!

Make sure unit is unplugged before installation!